How to replace window motor and regulator on 2007 Ford Taurus??

The instructions are similar for 2006 and 2007 ford Taurus Car models.

The details to replace Window motor and regulator are as follows:----

Window Systems

DIAGNOSIS & TESTING

REMOVAL & INSTALLATION

The instructions with diagrams are mentioned below:---

Diagnosis & Testing

The one-touch down (OTD) power window function allows the driver door window glass to completely lower with one button press. The driver window control switch is hardwired to the smart junction box (SJB) and door window regulator and motor. When the SJB senses a one-touch down request from the driver window control switch, the SJB supplies a ground to the OTD relay coil. The OTD relay then provides power to the driver window regulator motor, lowering the window. The OTD feature will function when the ignition switch is in the RUN or ACC position. The OTD feature also operates while the ignition is OFF and the delayed accessory time-out period has not expired or the driver door has not been opened.

Fig. Left front window circuit

Fig. Right front and left rear window circuits

Fig. Right rear window circuit

Removal & Installation

Motor & Regulator
Front Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the battery ground cable.
3. Remove the door trim panel screws.
   
   
   

   

   Fig. Front Door Trim Panel screw locations
4. Remove the watershield.
5. Remove the interior weatherstrip.
   
   CAUTION

   Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
   
   
   
   NOTE

   Lower the window to access the rivets.
6. Remove the 2 rivets retaining the front door window glass to the front door window regulator assembly.
7. Tilt the front door window glass forward and remove the glass.
8. Disconnect the front door window regulator motor electrical connector.
9. Remove the window regulator rivets.
10. Remove the front door window regulator.
    
    WARNING

    If the front door power window regulator counterbalance spring must be removed or replaced for any reason, make sure that the front door power window regulator arms are in a fixed position prior to removal to prevent possible injury during C-spring unwind.
11. Remove the bolts and the window regulator motor.
12. To install, reverse the removal procedure.

Rear Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the battery ground cable.
3. Remove the door trim panel screws.
   
   
   

   

   Fig. Rear Door Trim Panel screw locations
4. Remove the watershield.
5. Disconnect the rear door window regulator motor electrical connector.
6. Remove the rear door window regulator rivets.
7. Slide the rear door window regulator out of the rear door window glass run and bracket.
8. Remove the rear door window regulator.
   
   WARNING

   If the rear door window regulator counterbalance spring must be removed or replaced for any reason, make sure that the rear door power window regulator arms are in a fixed position prior to removal to prevent possible injury during C-spring unwind.
9. Remove the bolts and the window regulator motor.
   
   
   

   

   Fig. Window regulator motor bolts
10. To install, reverse the removal procedure.

Switch

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the battery ground cable.
3. Remove the door trim panel screws.
   
   
   

   

   Fig. Front Door Trim Panel screw locations
   
   
   
   

   

   Fig. Rear Door Trim Panel screw locations
   
   
   
   

   

   Fig. Removing the window switch
4. Disconnect the window control switch electrical connectors.
5. Release the 6 window control switch bezel tabs and remove the window switch.
6. To install, reverse the removal procedure.

This will help.

Thanks.

                     

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html