How to Replace Door locks on 2007 Ford Taurus?

The instructions are similar for 2006 and 2007 ford Taurus Car models.

The details to replace door locks is as follows : ----

Locks & Lock Systems

REMOVAL & INSTALLATION procedure is mentioned below: ---

Door Locks
Power Door Locks
Motor
Front Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the battery ground cable.
3. Remove the front door trim panel screws.
   
   NOTE

   To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
   
   
   
   
   

   

   Fig. Front Door Trim Panel screw locations
4. Remove the front door trim panel.
5. Position the watershield aside.
6. Disconnect the interior door handle cable guide.
7. Remove the window glass run channel bolt.
   
   
   

   

   Fig. Window Glass Run Channel Bolt
8. Remove the bolts and position the center window glass support aside.
   
   
   

   

   Fig. Center Window Glass Support bolts
9. Disconnect the exterior door handle actuating rod.
10. If equipped, unclip the lock rod from the lock cylinder.
11. Remove the door latch bolts.
    
    
    

    

    Fig. Door Latch Bolts
12. Disconnect the electrical connector(s).
13. Position the front door latch and cable assembly aside.
14. Remove the door ajar switch as follows:
    1. Lift the locking tab at the lower end.
    2. Rotate the door ajar switch counterclockwise.
    3. Remove the door ajar switch.
       
       
       

       

       Fig. Removing the Door Ajar Switch
15. Remove the door lock actuator as follows:
    1. Lift the locking tab.
    2. Slide the actuator off the latch assembly.
       
       
       

       

       Fig. Removing the Door Lock Actuator
16. To install, reverse the removal procedure.
    
    NOTE

    When installing the door lock actuator, the actuating lever must engage the actuating pin.

Rear Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the battery ground cable.
3. Remove the five rear door trim panel screws.
   
   NOTE

   To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
   
   
   
   
   

   

   Fig. Rear Door Trim Panel screw locations
4. Remove the rear door trim panel.
5. Disconnect the window regulator control switch electrical connector.
6. Position the watershield aside.
   
   CAUTION

   When removing the rivet's center pin, use care not to damage the door panel sheet metal.
7. Remove the lock rod bell crank rivet, and discard the bushing.
   
   
   

   

   Fig. Lock Rod Bell Crank Rivet
8. Disconnect the push button lock rod from the bellcrank.
9. Unclip and disconnect the exterior door handle actuating rod.
10. Remove the bolts, and position the rear door latch aside.
    
    
    

    

    Fig. Rear Door Latch Bolts
11. Remove the cover, and disconnect the rear door lock actuator cable.
12. Disconnect the electrical connector(s).
13. Remove the rear door latch.
14. Remove the door ajar switch as follows:
    1. Lift the locking tab at the lower end.
    2. Rotate the door ajar switch counterclockwise.
    3. Remove the door ajar switch.
       
       
       

       

       Fig. Removing the Door Ajar Switch
15. Remove the door lock actuator as follows:
    1. Lift the locking tab.
    2. Slide the actuator off the latch assembly.
       
       
       

       

       Fig. Removing the Door Lock Actuator
16. To install, reverse the removal procedure.
    
    NOTE

    When installing the door lock actuator, the actuating lever must engage the actuating pin.

Switch

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the battery ground cable.
3. Remove the front door trim panel screws.
   
   NOTE

   To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
   
   
   
   
   

   

   Fig. Front Door Trim Panel screw locations
4. Remove the front door trim panel.
5. Remove the door lock control switch.
6. To install, reverse the removal procedure.

This details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html