@

Tuesday, November 22, 2011

How to replace Water Pump on Honda Accord,Prelude Models?


Water pump is important part/component for car cooling system.Water pump maintenance is required,to keep water pump free from problems.But in case if it gets faulty then it has to be replaced.

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The procedure to replace cars water pump is as follows :----

Water Pump


REMOVAL & INSTALLATION


2.2L and 2.3L Engines


Click image to see an enlarged view
Fig. Direction of rotation of the water pump pulley


Click image to see an enlarged view
Fig. Water pump, gasket, and bolts
The original radio contains a coded anti-theft circuit. Obtain the security code number before disconnecting the battery cables.
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the accessory drive belts, the valve cover, and the upper timing belt cover.
  4. Set the timing at TDC/compression for the No. 1 piston.
  5. Remove the crankshaft pulley and lower timing belt cover.
  6. Remove the timing belt. Replace the timing belt if it is contaminated with oil or coolant or shows any signs of wear and damage. Refer to the procedure located in this section.
  7. If equipped with a Crankshaft Speed Fluctuation (CKF) sensor at the crankshaft sprocket, unbolt the sensor bracket and move the sensor out of the way. Cover the sensor with a shop towel to keep coolant off of it.
  8. Unbolt the water pump and remove it from the engine block.
To install:
  1. Clean the water pump and O-ring mating surfaces before installation.
  2. Install the water pump with a new O-ring. Coat only the bolt threads with liquid gasket and tighten them to 108 inch lbs. (12 Nm).
  3. Install the timing belt. Be sure it is fitted and adjusted properly. Refer to the procedure located in this section.
  4. If equipped, install the CKF sensor and tighten the bracket bolts to 108 inch lbs. (12 Nm).
  5. Install the lower belt cover and crankshaft pulley.
  6. Install the upper timing belt cover, the valve cover, and the accessory drive belts.
  7. Be sure the cooling system drain plug is closed. Refill and bleed the cooling system.
  8. Connect the negative battery cable and enter the radio security code.
  9. Start the engine, allow it to reach normal operating temperature, and check for coolant leaks.
2.7L Engine
  1. Disconnect the negative battery cable.
  2. Drain the coolant into a sealable container.
  3. Remove the timing belt covers and the timing belt. Refer to the procedure located in this section.
  4. Remove the timing belt tensioner.
  5. Remove the 9 water pump bolts, take note of their locations for reinstallation.
  6. Remove the water pump from the engine and discard the O-ring. Remove the dowel pins.
To install:
  1. Clean the water pump mounting surface and O-ring groove, then install the dowel pins to the engine.
  2. Install a new O-ring to the engine, then install the water pump. Be careful not to pinch the O-ring. Install the mounting bolts to their original locations. When tightening the bolts, be sure that the O-ring does not bulge out of the groove. Tighten the 6mm bolts to 108 inch lbs. (12 Nm), and tighten the 8mm bolts to 16 ft. lbs. (22 Nm).


Click image to see an enlarged view
Fig. Exploded view of the water pump-2.7L engine
  1. Inspect the water pump, making sure that the pump turns freely.
  2. Install the timing belt tensioner.
  3. Install the timing belt and timing belt covers. Refer to the procedure located in this section.
  4. Refill and bleed the air from the cooling system.
  5. Connect the negative battery cable and enter the radio security code.
3.0L Engine
  1. Remove the timing belt. Refer to the procedure located in this section.
  2. Remove the timing belt tensioner.
  3. Remove the 5 water pump mounting bolts, then remove the pump and seal.
To install:


Click image to see an enlarged view
Fig. Exploded view of the water pump mounting-3.0L engine
  1. Clean the seal groove and mating surfaces.
  2. Using a new seal, install the water pump. Tighten the bolts to 104 inch lbs. (12 Nm).
  3. Install the timing belt tensioner.
  4. Install the timing belt. Refer to the procedure located in this section.
  5. Refill the cooling system.
  6. Start the engine and check for leaks.
  7. Top off the cooling system if necessary after the engine has cooled.

-----------
This details will help.
---------------
For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

-----------------

Car will not crank?


-----------

Car has no spark?


-------------

How to troubleshoot car battery?

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?



-----------

car will turn over but will not start?



-----------------

Car wont start?


----------


No comments:

Post a Comment

@