How to replace Accessory Drive Belts on Buick Rendezvous?

The details to replace Accessory Drive Belts is as follows:----

Buick Rendezvous Accessory Drive Belts has four sections, View All:---

• ADJUSTMENT
• DRIVE BELT ROUTINGS
• INSPECTION
• REMOVAL & INSTALLATION

Adjustment

All engines use an automatic drive belt tensioner. No adjustment is necessary. If the tensioner is at Maximum travel, the belt is most likely stretched or the incorrect belt was installed.

Drive Belt Routings

 

Fig. Accessory drive belt routing-3.4L and 3.5L Enginess

 

Fig. Accessory drive belt routing-3.6L engines

Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation

3.4L & 3.5L Enginess

1. Rotate the drive belt tensioner in order to release the pressure on the drive belt.
   
   
   

   

   Fig. Illustration of the direction of the pressure on the belt
2. Remove the drive belt.
   
   
   

   

   Fig. Accessory drive belt routing-3.4L and 3.5L Enginess

To install:

1. Install the drive belt to all of the pulleys except the generator pulley.
2. Rotate the drive belt tensioner in order to install the drive belt over the generator pulley.
3. Ensure that the drive belt is aligned into the proper grooves of the accessory drive belt pulleys.
4. Ensure that the drive belt is properly routed.

3.6L Engine

1. Raise the vehicle.
2. Remove the right engine splash shield.
3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
4. Remove the drive belt from the generator.
5. Slowly release the drive belt tensioner.
6. Remove the drive belt from the accessory drive pulleys.
   
   
   

   

   Fig. Illustrates the position of the belt
   
   
   
   

   

   Fig. Accessory drive belt routing-3.6L engines

To install:

1. Install the right engine splash shield.
2. Lower the vehicle.
3. Install the drive belt to the accessory drive pulley.
4. Rotate the drive belt tensioner clockwise.
5. Install the drive belt to the generator.
6. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
7. Slowly release the drive belt tensioner.

These details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Latest Acura Accessory Drive Belts Diagrams and replacement instructions?

Accessory Drive Belts
ACCESSORY BELT ROUTING
ADJUSTMENT
INSPECTION
REMOVAL & INSTALLATION

The details are as follows :----

Accessory Belt Routing

 

Fig. Alternator-A/C Compressor accessory belt routing-2001-02 models

Fig. Power steering pump accessory belt routing-2001-02 models

Fig. Accessory belt routing-2003-06 models

Adjustment

Power Steering Pump Belt
2001-02 Models

1. Loosen the power steering pump mounting nut (A) and bolt (B).
2. Turn the adjusting nut (C) to get the proper belt tension, then retighten the mounting nut and bolt.
3. Start the engine and turn the steering wheel from lock-to-lock several times, then stop the engine and recheck the tension of the belt.
   
   
   

   

   Fig. Loosen the power steering pump mounting nut (A) and bolt (B). Turn the adjusting nut (C) to get the proper belt tension, then retighten the mounting nut and bolt

Except 2001-02 Models

Belt tension is automatically maintained by a belt tensioner. No adjustments are necessary.

Inspection

Power Steering Pump Belt
2001-02 Models

NOTE

There are two ways to inspect the belt tension: the Belt Tension Gauge Method and the Deflection Method. Both are outlined below.

Belt Tension Gauge Method

1. Attach the belt tension gauge to the belt with the gauge face toward the engine, and measure the tension of the belt. Follow the manufacture's instructions. If the belt is worn or damaged, replace it.
   
   NOTE

   Remove the belt tension gauge carefully to avoid hitting the gauge reset lever.
2. The tension should be:
   1. Used Belt: 88-120 lbs. (390-540 N)
   2. New Belt: 165-198 lbs. (740-880 N)
3. If you installed a new belt, run the engine for 5 minutes, then readjust the belt to the used belt specifications.
   
   
   

   

   Fig. Using a belt tension gauge to inspect the power steering pump belt tension

Deflection Method

1. Apply a force of 22 lbs. (98 N) and measure the deflection between the power steering pump pulley (A) and the crankshaft pulley (B).
2. The deflection should be:
   1. Used Belt: 0.51-0.65 in. (13.0-16.5mm)
   2. New Belt: 0.33-0.43 in. (8.5-11.0mm)
3. If you installed a new belt, run the engine for 5 minutes, then readjust the belt to the used belt specifications
   
   
   

   

   Fig. Apply a force of 22 lbs. then measure the deflection between the power steering pump pulley (A) and the crankshaft pulley (B)

Except 2001-02 Models

1. Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.
2. On 2001-02 models, check that the pointer (A) on the auto-tensioner housing is not beyond the edge of the indicator rib (B) on the tensioner base.
   
   
   

   

   Fig. On 2001-02 models, check that the pointer (A) on the auto-tensioner housing is not beyond the edge of the indicator rib (B) on the tensioner base

Removal & Installation

2001-02 Models
Alternator-A/C Compressor Belt

1. Note the radio security code and disconnect the negative battery cable.
2. Move the auto-tensioner (A) to relieve tension from the alternator belt (B), and remove the alternator belt.
3. Install the new belt in the reverse order of removal.
   
   
   

   

   Fig. Move the auto-tensioner (A) to relieve tension from the alternator belt (B), and remove the alternator belt

Power Steering Pump Belt

The power steering pump has two fasteners securing it to a bracket mounted on the engine. The right side locknut and fastener are installed through a slotted bracket and the left side fastener allows the pump to pivot.

1. Note the radio security code and disconnect the negative battery cable.
2. Loosen the right side locknut and left side pivot nut.
3. Move the pump by turning the adjustment nut on the right side bracket. Turn the adjustment nut counterclockwise to release the belt tension.
4. Remove the belt from the pulleys, one pulley at a time.

To install:

1. Install the belt around the pulleys, beginning with the largest pulley first.
2. Follow the adjustment procedure to correctly tension the belt.
3. Tighten the right side locknut and left side pivot bolt and then check the belt tension. If the belt tension is not within specification, repeat the adjustment procedure until the proper belt tension is achieved.
4. Reconnect the negative battery cable and enter the radio security code.

2005-06 Models

NOTE

For this procedure, you will need a Belt tension release tool (Snap-on YA9317) or equivalent.

1. Move the auto-tensioner (A) with the belt tension release tool to relieve tension from the drive belt (B), then remove the drive belt.
2. Install the new belt in the reverse order of removal.
   
   
   

   

   Fig. Accessory belt routing-2003-06 models

This details will help.
Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html