How to bleed power steering pump on Toyota?

The simple procedure is as follows :---

Bleeding

1. Check fluid level
2. Jack up front of vehicle and support it with stands
3. With the engine stopped, turn the wheel slowly from lock to lock several times.
4. Lower the vehicle.
5. Start the engine and run at idle for a few minutes.
6. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds. Repeat several times.
7. Stop the engine.
8. Check for foaming or emulsification of the power steering fluid.
9. If the system has to be bled twice specifically because of foaming or emulsification, check for fluid leaks in the system.

This will help.

Thanks.

See below latest solved car problems:-----

How to replace Tie Rod Ends on Chevy silverado 2500HD?

http://technoanswers.blogspot.in/2012/02/how-to-replace-tie-rod-ends-on-chevy.html

How to replace steering linkage on Chevrolet Silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/how-to-replace-steering-linkage-on.html

How to Replace power steering pump on Chevy silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

Power Recirculating Ball Steering Gear removal on Chevy silverado 2500 HD?

http://technoanswers.blogspot.in/2012/02/power-recirculating-ball-steering-gear.html

Chevy Silverado 2500 HD steering wheel replacing Procedure?

http://technoanswers.blogspot.in/2012/02/chevy-silverado-2500-hd-steering-wheel.html

Steering Wheel Locked?

http://schematicsdiagram.blogspot.com/2011/12/steering-wheel-locked.html

How to replace Power Rack and Pinion Steering Gear on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

How to replace Power Steering Pump on Acura Car Models?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

                                    

How to replace Steering Linkage on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html

How to replace Steering Wheel on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-wheel-on-acura.html

How to replace Power Steering Pump on 1999 Acura TL?

http://howtobyme.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

How to Disarming the Air Bag System?

http://technoanswers.blogspot.com/2011/12/how-to-disarming-air-bag-system.html

How to remove steering wheel on Chevrolet Malibu?

http://technoanswers.blogspot.com/2011/12/how-to-remove-steering-wheel-on.html

How to Remove Power steering Pressure Hose on Dodge Stratus

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

Car steering wheel makes noise?

http://schematicsdiagram.blogspot.com/2011/12/car-steering-wheel-makes-noise.html

Car makes clicking or tapping sound?

http://schematicsdiagram.blogspot.com/2011/12/car-makes-clicking-or-tapping-sound.html

How to replace power steering pump on Mitsubishi Diamante?

http://howtobyme.blogspot.com/2012/01/how-to-replace-power-steering-pump-on.html

How to replace Power Steering Pump on Acura Car Models?

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The procedure is as follows :----

Power Steering Pump

REMOVAL & INSTALLATION

1. Place a suitable drain pan under the vehicle, then disconnect the power steering hoses from the pump to drain the fluid.
2. Remove the belt by loosening the pump adjusting bolts and mounting bolts.
3. On the 3.5RL, Legend or Vigor, remove the air cleaner cover and air intake duct.
4. Cover the alternator (Integra, 2.2CL 2.3CL) or the crankshaft pulley (3.0CL 3.2TL) with some rags to protect it from any spilled power steering fluid.
5. Disconnect and plug the inlet and outlet hoses from the pump.

See Figures 1, 2, 3 and 4

Fig. Fig. 1: Power steering pump mounting-Integra shown

Fig. Fig. 2: Power steering pump mounting-2.2CL and 2.3CL

Fig. Fig. 3: Exploded view of the power steering pump-3.0CL

Fig. Fig. 4: Steering pump-to-engine attachment-Vigor shown

6. Unfasten the pump mounting bolt(s), then remove the pump from the vehicle.

WARNING

Do not turn the steering wheel with the pump removed.

7. Cover the opening of the pump with a piece of tape to prevent any foreign material from entering the pump.
8. If you are replacing the pump and need to transfer the pulley, hold the steering pump in a suitable soft-jawed vise, hold the pulley with a suitable universal pulley holding tool, then remove the pulley nut and pulley/
9. Installation is the reverse of the removal procedure. Bleed the power steering system.

SYSTEM BLEEDING

WARNING

Use only genuine Honda power steering fluid. Any other type or brand of fluid will damage the power steering pump.

1. Lift the power steering reservoir off of its mount. Disconnect the return hose from the steering rack at the reservoir. Immediately plug the reservoir inlet to prevent fluid loss and contamination. Don't disconnect the hose that connects the pump to the reservoir.
2. Insert a length of rubber tubing into the return hose and route the tubing into a drain container.
3. With the engine running at idle, turn the steering wheel lock-to-lock several times until fluid stops running out of the hose. Immediately shut the engineOFF .

See Figure 5

Fig. Fig. 5: Bleeding the air from the power steering system

4. After servicing, reconnect the reservoir return line. Fill the reservoir to the upper line with genuine Honda power steering fluid.
5. Run the engine at idle and turn the steering wheel lock-to-lock several times to bleed air from the system and fill the rack valve body.
6. Recheck the fluid level and add more if necessary. Don't overfill the reservoir.
7. Check the power steering system for leaks.
8. Lower the vehicle.

See Figure 6

Fig. Fig. 6: Torque Specifications

---------------

This details will help.

Thanks.

----------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

Car wont start?

http://howtobyme.blogspot.com/2011/10/car-wont-start.html

----------