Replace Ford Explorer Slave Cylinder?

Slave (Actuator) Cylinder
REMOVAL & INSTALLATION Procedure will work for
Lincoln Aviator, Ford Explorer, Exp Sport, Exp Sport-Trac, Mercury Mountaineer 2000-2005.

The instructions with proper details is follows :----

Removal & Installation

1. Before servicing the vehicle, please familiarize yourself with safety procedures.
2. Remove the transmission.
   
   NOTE

   Inspect the clutch housing for traces of fluid. If brake fluid is visible, install a new clutch slave cylinder.
3. Remove the bolts. Remove the clutch slave cylinder.
4. Inspect the clutch slave cylinder for the following:
   
   CAUTION

   The clutch release hub and bearing is pre-lubricated and should not be cleaned with solvent. The clutch release hub and bearing are replaced as an assembly. Do not disassemble for inspection or replacement.
   
   
   
   
   Worn or damaged boot.

   Leaking fluid.

   Contract and return smoothly.
5. Inspect the clutch release bearing as follows:
   
   
   Rotate the outer race while applying pressure. If the bearing rotation is rough, install a new clutch slave cylinder.

   Inspect for wear or damage.

   If wear pattern is continuous (not segmented) and the wear appears to be deep in bearing face, install a new clutch slave cylinder.

To install:

1. Installation is the reverse of the removal procedure.
2. Observe the following tightening torques:
   
   
3. Position the clutch slave cylinder to the transmission and install the bolts.
   1. Tightening torque 9 ft. lbs. (12 Nm).
4. Bleed the clutch hydraulic system.

1. Before servicing the vehicle, please familiarize yourself with safety procedures.
2. Remove the transmission.
   
   NOTE

   Inspect the clutch housing for traces of fluid. If brake fluid is visible, install a new clutch slave cylinder.
3. Remove the bolts. Remove the clutch slave cylinder.
4. Inspect the clutch slave cylinder for the following:
   1. Worn or damaged boot.
   2. Leaking fluid.
   3. Worn or damaged bearing.
5. Inspect the clutch release bearing as follows:
   1. Rotate the outer race while applying pressure. If the bearing rotation is rough, install a new clutch slave cylinder.
   2. Inspect for wear or damage.

To install:

1. Installation is the reverse of the removal procedure.
2. Position the clutch slave cylinder to the transmission and install the bolts.
   1. Tightening torque 15 ft. lbs. (20 Nm).
3. Install the transmission.
4. Depress and release the clutch pedal five full strokes.

This will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

How to replace Slave Cylinder and bleed Hydraulic system on Acura Car models?

If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.

The procedure is as follows :----

Slave Cylinder

REMOVAL & INSTALLATION

1. Locate the slave cylinder.
2. Remove the flare fitting and steel line from the slave cylinder assembly.

See Figure 1

Fig. Fig. 1: Disconnecting the hydraulic line from the slave cylinder

3. Remove the slave cylinder from the clutch housing by removing the attaching bolts.
4. Installation is the reverse of the removal procedure

Use only DOT 3 or 4 brake fluid to refill the clutch hydraulic system.

5. Fill and bleed the clutch system, using a suitable DOT 3 or 4 brake fluid..

HYDRAULIC SYSTEM BLEEDING

Use only DOT 3 or 4 brake fluid from a clean, sealed container, in the clutch master and slave cylinders. As brake fluid will damage the vehicle's paint, clean up any spills immediately.

1. Fit a flare or box end wrench onto the slave cylinder bleeder screw.
2. Attach a rubber tube to the slave cylinder bleeder screw and suspend it into a clear drain container partially filled with brake fluid.
3. Fill the clutch master cylinder with brake fluid.
4. Open the bleeder screw and press the clutch pedal to the floor.
5. Close the bleeder screw.
6. Release the clutch pedal and recheck the reservoir fluid level. Top off if necessary.
7. Continue the above procedure until no more bubbles appear in the tube.
8. Top off the clutch master cylinder reservoir with brake fluid.

---------------

This details will help.

Thanks.

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

Car wont start?

http://howtobyme.blogspot.com/2011/10/car-wont-start.html

----------