How to replace water pump on Acura?

Water Pump
REMOVAL & INSTALLATION: ---

1. Before servicing the vehicle, refer to the precautions section.
2. Drain the cooling system.
3. Remove or disconnect the following: 
   
   
   Negative battery cable

   Accessory drive belts

   Front cover

   Timing belt

   Timing belt tensioner

   Water pump 
    
   
   

   Fig. Exploded view of the water pump mounting

To install:

1. Install or connect the following:
   
   
   Water pump. Use a new O-ring seal and tighten the bolts to 105 inch lbs. (12 Nm).

   Timing belt tensioner

   Timing belt

   Front cover

   Accessory drive belts

   Negative battery cable
2. Fill the cooling system.
3. Start the engine and check for leaks.

The details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Crankshaft Damper Balancer replacing on Acura?

Crankshaft Damper (Balancer)
REMOVAL & INSTALLATION

The details are as follows :-----

2001-02 Models

NOTE

This procedure requires the use of the following special tools or their equivalents:

Holder handle 07JAB-001020A

Holder attachment, 50mm, offset 07MAB-PY3010A

Socket, 19mm 07JAA-001020A or a commercially available 19mm socket

1. Hold the pulley with the holder handle (A) and holder attachment (B).
2. Remove the bolt with a heavy duty 19mm socket (C) and breaker bar. 
   
   
   
   Fig. Hold the pulley with the holder handle (A) and holder attachment (B). Remove the bolt with a heavy duty 19 mm socket (C) and breaker bar-2001-02 models
3. Remove any oil from the pulleys (A), crankshaft (B), bolt (C), and washer (D). Clean and lubricate the points shown in the accompanying illustration.
   
   
   

   

   Fig. Remove any oil from the pulleys (A), crankshaft (B), bolt (C), and washer (D). Clean and lubricate the points shown-2001-02 models

To install:

1. Install the crankshaft pulley, and tighten as follows: Do not use an impact wrench:
   1. Hold the pulley with the holder handle (A) and holder attachment (B).
   2. Tighten the bolt with a torque wrench and 19mm socket (C) to 181 ft. lbs. (245 Nm).
      
      
      

      

      Fig. To tighten the crankshaft pulley bolt, hold the pulley with the holder handle (A) and holder attachment (B), then tighten the bolt with a torque wrench and 19mm socket (C) -2001-02 models

2003-06 Models

NOTE

This procedure requires the use of the following special tools or their equivalents:

Holder handle 07JAB-001020A

Holder attachment, 50mm, offset 07MAB-PY3010A

Socket, 19mm 07JAA-001020A or a commercially available 19mm socket

1. Remove the right front wheel.
2. Remove the splash shield.
3. Remove the drive belt.
   
   
   

   

   Fig. Remove the splash shield-2003-06 models
4. Hold the pulley with the holder handle (A) and holder attachment (B).
5. Remove the bolt with a heavy duty 19mm socket (C) and breaker bar, then remove the crankshaft pulley.
   
   
   

   

   Fig. Hold the pulley with the holder handle (A) and holder attachment (B). Remove the bolt with a heavy duty 19mm socket (C) and breaker bar, then remove the crankshaft pulley-2003-06 models

To install:

1. Remove any oil or clean the pulleys (A), crankshaft (B), bolt (C), and washer (D). Lubricate new engine oil as shown in the accompanying illustration.
   
   
   

   

   Fig. Remove any oil or clean the pulleys (A), crankshaft (B), bolt (C), and washer (D). Lubricate new engine oil as shown-2003-06 models
2. Install the crankshaft pulley, and tighten the bolt as follows. Do not use an impact wrench.
   1. Hold the pulley with the handle (A) and holder attachment (B), then tighten the bolt to 47 ft. lbs. (64 Nm) with a torque wrench and 19mm socket (C).
   2. Mark (D) the bolt head and crankshaft pulley as shown, then tighten the bolt an additional 60 º (The mark on the bolt head line up with the mark on the crankshaft pulley).
      
      
      

      

      Fig. Hold the pulley with the handle (A) and holder attachment (B), then tighten the bolt to 47 ft. lbs. with a torque wrench and 19 mm socket (C). Mark (D) the bolt head and crankshaft pulley as shown, then tighten the bolt an additional 60 º (The mark on the bolt head line up with the mark on the crankshaft pulley).
3. Install the drive belt.
4. Install the splash shield.
5. Install the right front wheel.

This details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html